Performed annual cleaning and service on the oil-fired heating system, including removal and cleaning of the burner nozzle and ignition electrode assembly on the Beckett GenSys 7505 burner. Inspected the burner housing, motor, control, and fuel pump assembly, noting corrosion on the fuel pump, and restored the system to proper operation to address the customer's reported lack of heat at the 72-degree thermostat setting.

Replaced 15-year-old electric Whirlpool water heater that was leaking at the base. Removed and disposed of failed unit, installed new Whirlpool electric water heater with proper connections and controls. Additionally removed old water treatment system that had been previously discussed and was no longer in use. Verified all electrical connections, tested unit operation, and confirmed proper functionality of new installation.

Responded to service call for oil heating system not operating after homeowner replaced thermostat batteries. Upon arrival, found Honeywell Home Pro Series digital thermostat displaying numbers but system failing to call for heat. Verified thermostat was receiving power and display was functioning properly at 71 degrees in heat mode with fan set to auto. Inspected basement mechanical room and examined oil-fired heating system, humidifier unit, and associated ductwork connections. Diagnosed thermostat programming issue following battery replacement which reset system settings. Reprogrammed thermostat to correct parameters and verified proper communication between thermostat and heating system. Cycled system through complete heating cycle to confirm proper operation and heat delivery throughout home.

Completed natural gas furnace tune-up and maintenance on existing Lennox unit. Performed comprehensive system inspection, verified gas pressure and combustion efficiency, cleaned burner assembly, checked electrical connections with amp draw reading of 124.3A, inspected heat exchanger for cracks, tested safety controls, and verified proper operation of blower motor and ductwork. System operating within manufacturer specifications with no issues found.

Completed comprehensive oil cleaning and maintenance service on New Yorker oil boiler system. Performed standard tune-up procedures including combustion chamber inspection, burner nozzle replacement, oil filter change, and system pressure testing as evidenced by gauge readings. All components operating within manufacturer specifications upon completion.

Replaced failed water heater with new A.O. Smith 50-gallon electric storage tank model EX-50EA50DV rated at 240V/4500W, installed new expansion tank, and replaced pressure reducing valve with like unit to resolve high water pressure issues affecting Moen whole house automatic shut-off system.

Completed comprehensive cleaning and servicing of 1999 Armstrong oil heating system. During inspection, identified elevated flue temperatures indicating potential soot buildup or oversized nozzle requiring monitoring and possible downsizing. Documented system performance with electrical readings showing 642mA and photographed ductwork connections; recommended fall follow-up to assess combustion efficiency and determine if nozzle adjustment is necessary.

Responded to emergency call for leaking main water shut-off valve. Upon arrival, confirmed water was already shut off at exterior main to control active leak. Replaced faulty main shut-off valve assembly with new brass ball valve with red handle. Installed valve within recessed wall access panel box with proper gasket seal and secured with white PVC connections on both sides. Tested valve operation, confirmed no leaks, and restored water service to property.

Completed oil heating system tune-up and cleaning service on a 2017 Thermo Pride unit under partner membership program. Performed comprehensive maintenance including combustion chamber inspection, burner nozzle replacement, fuel filter service, and blower assembly cleaning. System tested and confirmed operating within manufacturer specifications with proper ignition, flame pattern, and heat output.

Completed CPM heating inspection on Burnham boiler system installed in September 2019. Verified operational status with system displaying supply temperature at 162°F, return temperature at 142°F, stack temperature at 138°F, and firing rate at 61%. Inspected Amtrol expansion tank and associated components, confirmed proper system pressurization and function, documented all readings and equipment conditions with photos.

Completed CPM oil heating inspection at property with no existing oil equipment found on file. Documented HVAC equipment with photographs showing Samsung heat pump system installed in August 2021, positioned on exterior concrete pad with refrigerant lines running along foundation wall. Heat pump evaluation scheduled as separate service to verify system operation and performance.

Responded to service call for reported toilet float issue. Upon inspection, examined all internal tank components including fill valve with functional red cap, flush valve assembly with intact flapper seal, and overflow tube. All mechanisms were found to be in proper working condition with normal water levels and no signs of malfunction or component failure. Determined that existing float and fill valve system did not require replacement at this time.

Responded to two plumbing concerns: investigated intermittent high-pitched humming noise occurring when multiple water fixtures were in use, which stopped when powder room toilet was flushed. Accessed plumbing system through drywall opening to diagnose water hammer issue and inspected valve assembly. Additionally addressed sewage odor in main bathroom by examining drain system and replaced defective valve fixture to resolve both the noise issue and potential venting problem causing the odor.

Responded to no-heat call on Thermo Pride LP furnace installed October 2024. Upon arrival, found unit completely non-operational with house temperature at 66°F. Performed diagnostic testing using multimeter to check electrical components including capacitor and control circuits. Identified blockage and debris accumulation in condensate drain tubes preventing proper operation. Cleared obstructions from plastic drain lines to restore drainage function. Addressed previously noted issue with water leaking from inducer/exhaust connection that was documented during prior AC maintenance but not completed. Applied high-temperature silicone sealant to seal connection between inducer motor and exhaust piping to prevent moisture intrusion. Verified all electrical connections, tested system operation, and confirmed unit restored to proper heating function with adequate airflow through floor registers.

Completed comprehensive heating tune-up and maintenance on 2013 Miller propane furnace system. Performed full system inspection including examination of heat exchanger, burner assembly, ignition components, and blower motor operation. Verified all electrical connections, control board functionality, and safety mechanisms are operating within manufacturer specifications. System tested and confirmed to be functioning properly for the heating season.

Responded to customer complaint of high water bills despite discontinuing outdoor watering. Inspected both toilets in residence and identified continuously running mechanisms as primary cause of excessive water consumption. Found deteriorated internal components (flappers, fill valves, and flush mechanisms) in both units requiring replacement. Observed corroded hardware and compromised wax ring seals at base of fixtures with visible water staining on floor surfaces. Presented repair options including minor rebuild with replacement of internal components, major rebuild with new flanges and complete gut replacement, and full toilet replacement with standard or pressure-assisted models. Documented existing conditions with photographs showing base deterioration, floor staining, and corroded flush mechanisms. Provided customer with detailed estimates for each repair option to address ongoing water loss issue.

Replaced two toilets in main warehouse facility. Previous units exhibited whistling noise at idle that ceased when flushed, indicating faulty fill valve operation. Old toilet tanks showed significant deterioration with extensive mineral deposits, brown staining, and corroded interior surfaces from hard water exposure. Removed existing toilets and installed new standard white porcelain units with updated fill valve and flush valve assemblies. Tested installations for proper operation and verified absence of previous noise issues.

Completed comprehensive oil cleaning and service on Thermo Dynamics oil boiler originally installed in December 2016. Replaced .85/80B nozzle and 1A-25A oil filter, inspected fuel pump assembly and hydraulic components, and verified all system connections and electrical terminals were secure and functioning properly. System tested and left in full operational condition.

Replaced deteriorated heat tape on pipes located in crawl space beneath structure. Removed old damaged heat tape from water supply lines and installed new heat tape with proper spacing and securing methods. Ensured all electrical connections were properly made and insulation was correctly positioned around treated pipes. Work was approved by customer via phone prior to service completion.

Responded to kitchen sink leak caused by failing couplings beneath the sink. Replaced defective coupling connections on water supply lines to eliminate active leak. Subsequently installed customer-supplied kitchen faucet with pull-down spray head, mounting unit on existing countertop opening and connecting to supply lines. Tested all connections for proper water flow and verified no leaks present at completion.

Responded to basement water leak complaint. Upon inspection, identified water accumulation near floor drain and exterior drainage system. Examined basement floor drain assembly and exterior yard drain grate for potential sources of water intrusion. Floor drain showed signs of moisture exposure with visible biological growth around fastening points, indicating chronic dampness. Exterior drain grate exhibited heavy rust and debris accumulation, suggesting potential blockage or restricted water flow. Assessed drainage piping system to rule out water softener malfunction versus drain line issues. Documented conditions with photographic evidence for reference.

Completed mobile home water heater replacement after initial installation revealed oversized unit for confined space. Returned with properly sized water heater to accommodate tight clearances in utility closet. Installed new water heater with copper flex lines, drain pan, and proper electrical connections in white-painted enclosure with adequate clearance measurements verified.

Completed oil clean and service on heating system experiencing intermittent error codes requiring manual resets since another contractor's February cleaning. Performed thorough cleaning and inspection of boiler unit, expansion tank, piping connections, and associated controls to restore reliable operation and eliminate nuisance shutdowns.

Performed preventive maintenance tune-up on Goodman heat pump system located in attic, including thorough blower wheel cleaning which had accumulated significant debris from extended service without maintenance. Conducted complete system diagnostics with electrical testing at service panel, verifying proper amperage draw and circuit operation. Inspected outdoor condenser unit, evaluated thermostat operation for reported intermittent issues, and confirmed system is functioning properly with all components operating within manufacturer specifications.

Responded to service call for toilet leaking into basement when flushed. Upon arrival, water supply had been shut off to prevent further damage. Inspected two-piece toilet installation, tank components, and flush mechanism to identify source of leak. Completed necessary repairs to resolve leak issue and restore proper toilet function without water entering basement area.