HVAC & Plumbing Services in Mertztown, PA

Completed comprehensive AC tune-up and maintenance on two systems for new customer: main house Carrier unit (less than 10 years old) and separate in-law suite system. Performed standard preventive maintenance procedures including inspection of electrical components, circuit boards, compressor operation, and refrigerant levels. Verified system temperatures and operational parameters using calibrated digital instrumentation. Both systems found to be operating within normal specifications with minor age-related wear noted on wiring and internal components.

Responded to outdoor faucet that would not shut off completely, causing continuous leak. Inspected hose bib and surrounding plumbing system, documenting existing conditions with photos. Presented customer with repair options including full faucet replacement and installation of an isolation valve for improved water control and future maintenance access.

Completed comprehensive preventive maintenance inspection on residential air conditioning system. Accessed and inspected outdoor condenser unit electrical components including control board, wiring connections, and safety controls; all terminals secure with no signs of overheating or deterioration. Evaluated indoor evaporator coil assembly in attic space, confirming proper refrigerant flow through copper tube circuits and heat exchanger fins. System operational and performing within normal parameters.

Responded to a clogged shower head issue where water flow remained restricted even after removing the fixture. Investigated the shower arm pipe and confirmed an internal blockage using a probe. Inspected the property's cast iron plumbing system and documented areas of concern, including deteriorated pipe sections in the basement area showing signs of age and potential corrosion. Photographed the clogged shower arm opening revealing significant mineral buildup and debris accumulation, as well as aging cast iron pipes with severely deteriorated paint indicating possible moisture exposure. Customer has access to an alternative upstairs shower during resolution of the issue.

Completed CPM air conditioning inspection at residential property. Documented HVAC system electrical control compartment and circuit board assembly with photographs for equipment records as requested. Inspected control board components including relays, capacitors, resistors, and integrated circuits; verified wiring connections across multiple circuits with proper color-coded conductors and grounding. All electrical components and connections found in serviceable condition with normal wear consistent with system age.

Performed comprehensive tune-up and maintenance on Samsung mini-split system installed in June 2017, confirming unit is operating without issues. Inspected and documented deteriorated refrigeration line insulation that was falling off in pieces along the exterior wall run, with exposed copper lines visible through damaged insulation sections. Evaluated electrical connections, capacitor, and terminal block inside equipment enclosure, verifying all wiring connections are secure and components are functioning properly.

Completed water treatment system replacement at customer facility. Received materials, staged equipment in install bay, and coordinated scheduling for three-hour installation window. Successfully installed new water treatment unit, verified proper operation of Delta Manifold 2 control system, and confirmed all connections and settings were functioning correctly upon completion.

Completed preventive maintenance inspection on Tempstar heat pump system (March 2014 manufacture date) in cooling mode. Performed comprehensive tune-up including inspection of indoor air handler components, ductwork connections, and thermostat operation. All system components found operating within normal parameters with thermostat displaying proper readings and responsive controls.

Responded to after-hours emergency call to address water leak on water treatment system. Successfully replaced faulty component and restored proper operation, eliminating active leak and returning unit to normal service.

Responded to service call for residential air conditioning system blowing warm air with inadequate cooling performance. Upon inspection, identified issues with refrigerant line connections and electrical wiring at outdoor condenser unit. Secured copper refrigerant lines in mounting bracket with proper insulation sleeves to prevent thermal loss. Verified and reconnected electrical connections at junction box using appropriate wire connectors to ensure proper power supply to compressor and condenser fan motor. Tested system operation and confirmed proper cooling function restored with adequate airflow and temperature differential.

Completed comprehensive air conditioning tune-up and maintenance inspection on a 5-year-old Lennox heat pump system with LP backup heat. Performed multi-point system evaluation including inspection of electrical components, circuit boards, wiring connections, and condenser unit operation. All components found to be functioning properly with no issues identified during the inspection.

Responded to follow-up service call for cooling performance verification after recent after-hours assistance. Performed comprehensive system inspection of upstairs air conditioning unit. Conducted visual examination of exterior condensing unit and interior air handler components, including ductwork and insulation integrity in attic space. Verified system operation, airflow, and cooling output. Documented equipment condition with photographs showing exterior unit installation, electrical connections, and attic ductwork routing. System confirmed operational with adequate cooling capacity. Advised on proper filter maintenance for upstairs unit.

Completed blower wheel cleaning on HVAC system as previously sold and scheduled. Unit interior showed significant accumulation of dirt and debris on blower wheel assembly, which was thoroughly cleaned to restore proper airflow and system efficiency.

Completed comprehensive air conditioning tune-up and system inspection. Performed thorough evaluation of electrical components including capacitor and control board functionality, verified all wire connections within the control panel, and inspected the air handler unit located in the crawl space. All components found to be operating within normal parameters, and membership program options were presented to the customer.

Responded to customer complaint regarding excessive indoor humidity levels causing damage to wooden furniture and flooring during cooling season. Documented HVAC system specifications and current operating parameters for future diagnostic work scheduled when ambient conditions allow proper system evaluation. Customer reported humidity-related wood swelling has decreased by approximately 1/4" since switching to heating mode, confirming correlation between AC operation and moisture issues requiring further investigation of system dehumidification performance.

Performed CPM A/C inspection on SmartComfort system installed in October 2023 with 16x25x1 filter. Investigated customer concern regarding condensate drainage system after homeowner discovered disconnected condensate tubing exiting the home with no proper connection to remove water from underneath the structure. Inspected condensate line routing, verified system operation, and documented equipment labels and exterior condensate discharge point with photos to assess proper drainage functionality and determine necessary repairs to condensate piping system.

Responded to cold water leak under mobile home where crimped tee fitting was identified as the source of the leak. Replaced leaking polybutylene tubing with PEX piping for both hot and cold water lines in the crawl space. Water had been shut off to the home prior to arrival and was restored upon completion of repairs.

Performed maintenance inspection on Fleck 560 water softener system experiencing excessive salt consumption, which had doubled from normal usage of 40 pounds to 80 pounds per month. Conducted comprehensive water quality testing and water pressure diagnostics to assess system performance. Upon inspection, noted that resin media has not been replaced since original installation in October 2014, indicating need for future media replacement to restore proper regeneration efficiency and salt consumption rates.

Replaced two shut-off valves feeding the bathroom to eliminate active leaking before customer's vacation. Installed new quarter-turn ball valves on copper supply lines to ensure reliable water control and prevent potential water damage during extended absence.

Water softener check

Leaking drain line

Completed multi-point repair on residential HVAC system requiring two-person crew. Re-leveled downstairs indoor air handler unit, performed blower wheel cleaning to restore proper airflow, replaced two failed capacitors (verified with diagnostic testing equipment), and installed new condensate float switch to prevent overflow issues.

Responded to service call for Lennox air conditioning system not maintaining temperature with indoor unit freezing up in basement. Upon inspection, found evidence of previous refrigerant addition and signs of system age with visible corrosion on components. Diagnosed freezing coil condition, documented electrical connections at outdoor unit and indoor air handler condition with rust present on mounting brackets and housing. System installed approximately 11 years ago with recent filter change completed by occupant prior to service visit.

Responded to after-hours emergency for reported toilet leak. Upon arrival, inspected bathroom plumbing fixtures and identified water seepage from toilet supply line connection at the angle stop valve. Tightened compression fitting on braided supply line and verified all connections at the chrome shut-off valve were secure. Tested system by cycling water supply and flushing toilet multiple times to confirm leak was resolved with no further water discharge observed.

Responded to service call for comfort height toilet experiencing incomplete tank filling, resulting in inadequate flushing performance. Upon inspection, found toilet tank with significant mineral deposits, staining, and discolored water indicating aging flush valve and fill valve assembly. Tank required manual valve manipulation to achieve proper water level for effective flush. Performed mid-job assessment and presented repair options including immediate repair, partial tank rebuild, complete tank rebuild, standard flush toilet replacement, pressurized flush toilet replacement, and flange repair as needed. Documented existing water damage to surrounding flooring and baseboard, showing extensive staining and discoloration. Deployed water extraction equipment to address moisture issues in affected area. Adjusted fill valve mechanism and tested flush cycle to restore proper tank filling and flushing operation.