HVAC & Plumbing Services in Fleetwood, PA

Completed comprehensive heat pump tune-up and preventative maintenance on two systems under CPM cooling agreement. House unit is a Lennox system installed in November 2019; garage unit is a Daikin Fit installed in August 2023. Inspected electrical control panels, wiring connections, and terminal strips on both systems. Cleaned blower wheel as needed. Checked refrigerant lines, capacitors, and outdoor condenser units. Noted biological growth present on outdoor unit covers and surrounding concrete surfaces. All electrical connections verified secure, systems operating within normal parameters. Both heat pumps tested and confirmed functioning properly for cooling season.

Replaced defective stepping motor on Daikin mini split system to restore proper operation. Part had been previously ordered and collected from warehouse stock upon arrival. System tested and confirmed operational following repair.

Completed full HVAC system change-out including installation of Moyer Comfort Series propane gas furnace and matching heat pump with MPG filter and humidifier. Replaced existing ductwork with new 10x24 return trunk and drop, 8x24 supply trunk, and 6-inch plenum takeoff to ensure proper airflow distribution. Addressed severely contaminated insulated ductwork showing extensive dirt accumulation and staining throughout the interior surfaces, replacing compromised components to restore system efficiency and indoor air quality.

Completed comprehensive preventive maintenance inspection on Rheem air conditioning system installed in 2016 with compressor replacement performed in November 2025. Thoroughly inspected control board, electrical connections, and wiring harness; verified all terminals secure and components functioning properly. Documented control board assembly and circuit connections with detailed photographs for service records. Renewed annual Gold Membership for continued preventive maintenance coverage.

Completed full system change-out, removing existing York heat pump and installing new Moyer Comfort Series heat pump with air handler in basement mechanical room. Installation included proper refrigerant line connections, ductwork integration with existing metallic supply plenum, condensate drain piping with PVC routing, and electrical connections per manufacturer specifications.

Responded to no cooling complaint on 2017 Amana system with compressor and fan not running. Diagnosed failed blower motor and replaced unit with new motor. Verified proper operation of all system components, confirmed adequate airflow, and restored full cooling functionality to the system.

Responded to no cooling call on 25+ year old residential air conditioning system. Found indoor unit fan operating but delivering warm air with outdoor condensing unit completely non-operational. Diagnosed failed run capacitor preventing compressor and outdoor fan motor from starting. Removed defective capacitor and installed replacement unit with proper microfarad rating and voltage specifications. Verified outdoor unit startup, confirmed compressor operation, and tested system performance. Unit cooling properly upon departure.

Completed scheduled maintenance and component replacement on residential HVAC system. Replaced REME HALO bulb with new unit from inventory. Installed new single-phase run capacitor rated up to 20 MFD to restore proper compressor operation. Performed thorough cleaning of blower wheel assembly, removing accumulated dust and debris from blades and housing to restore optimal airflow and system efficiency. All components tested and verified operational upon completion.

Performed comprehensive air conditioning tune-up on existing HVAC system. Replaced condensate drain line to prevent water damage and ensure proper drainage. Inspected air handler interior components including blower assembly, capacitor, control board, and electrical connections; all components found to be in proper working condition with secure wiring.

Responded to service call regarding loss of power to HVAC system following work performed by handyman near generator transfer switch. Upon arrival, inspected main electrical panel and generator transfer panel. Found that circuit breaker feeding the generator sub-panel had been inadvertently switched, disrupting power distribution to the air conditioning and furnace systems while leaving the generator itself operational. Identified the "GEN PANEL FEED" breaker in the main distribution panel and verified proper positioning. Reset the affected circuit breaker to restore normal power flow to the HVAC equipment through the transfer switch system. Tested air conditioning and furnace operation to confirm full restoration of service. Documented electrical panel configuration with photos showing breaker positions and circuit directory for service records. All systems returned to normal operation with no additional issues identified.

Replaced damaged electrical whip on outdoor air conditioning unit with new whip assembly including 3/4" straight fitting at disconnect box. Collected payment for completed work and membership dues.

Responded to no cooling call on Trane air conditioning system displaying error code 126. Upon arrival, found outdoor unit breaker tripped. Reset both indoor and outdoor breakers and attempted system restart. Unit powered up but immediately returned same error code 126, indicating a persistent fault condition. As a safety precaution, shut down system at both breaker locations to prevent potential damage to components or electrical hazards. Accessed outdoor unit and inspected internal electrical components, control boards, wiring harnesses, and compressor assembly. System requires further diagnostics to identify root cause of error code and breaker trip.

Replaced leaking natural gas power vent water heater with new unit, including installation of new expansion tank. The original water heater was failing at the base, necessitating complete replacement. Connected all necessary utilities including gas line, copper water supply lines, and PVC venting. Exercise caution with existing valve on top of old unit due to corrosion concerns to prevent additional water damage during removal.

Completed comprehensive preventive maintenance inspection on residential air conditioning system installed in December 2019. Performed thorough examination of indoor air handler components including blower motor assembly, electrical connections, control board, and wiring harnesses. Verified all wire connections were properly secured with zip ties and showed no signs of overheating or deterioration. Inspected cylindrical blower motor and mounting brackets for proper operation and structural integrity. Examined control board for any signs of component failure, loose connections, or burnt circuits - all found to be in good working condition. Checked air filter condition and airflow. Inspected outdoor condensing unit including refrigerant lines, shut-off valves, and plumbing connections. Verified red shut-off valve operation and checked all copper and PVC piping for leaks or damage. All mechanical and electrical components functioning within normal parameters. System operational.

Completed outdoor coil cleaning on HVAC system, removing heavy accumulation of dirt and debris from condenser unit. Performed indoor air quality upgrade by installing REME unit with electrical connections to air handler control board. Verified all electrical connections, tested system operation, and confirmed proper function of newly installed IAQ equipment.

Responded to service call for malfunctioning glass shower door with faulty hinge/pivot point causing door to scrape bottom track. Inspected shower enclosure, identified worn pivot mechanism and misalignment issue at base of door frame. Documented existing conditions including visible corrosion at metal trim where door meets tile flooring.

Completed comprehensive air conditioning tune-up and maintenance on existing residential cooling system, approximately 5 years old. Performed standard diagnostic testing using Fieldpiece SC260 multimeter, measuring electrical parameters including voltage and capacitance readings to verify proper system operation. All components inspected and system operating within normal specifications.

Responded to customer complaint of toilet whistling when flushed and constant dripping into bowl. Upon inspection, found deteriorated fill valve assembly with mineral buildup and sediment accumulation throughout tank interior. Identified faulty fill valve causing whistling noise and defective flush valve allowing continuous water seepage into bowl. Documented existing conditions showing significant mineral deposits, rust-colored staining, and discolored water indicating aged components requiring replacement to restore proper operation and eliminate water waste.

Completed comprehensive water treatment system installation including Hague water softener, WR-120 well water storage tank, and whole house filtration system on main water supply line. All equipment installed with copper piping connections in confined utility space, with proper integration to existing plumbing infrastructure. System tested and operational upon completion.

Completed comprehensive maintenance inspection on 3-year-old heat pump system. Performed electrical diagnostics using clamp meter on indoor air handler unit, measuring blower motor amperage at 5.92 amps, confirming proper operation within manufacturer specifications. Proceeded to outdoor condensing unit where capacitor testing was conducted, measuring 3299 microfarads to verify component integrity and starting capabilities. All electrical connections inspected and found secure, system operating efficiently with no issues identified.

Responded to no cooling complaint on Carrier heat pump system installed in 2002. Upon arrival, diagnosed indoor blower motor failure preventing air circulation. Replaced defective blower motor with new unit and verified proper operation. Inspected heavily soiled air filters showing significant dust and debris accumulation, recommended immediate replacement to prevent future system issues and maintain proper airflow. System restored to full cooling operation and tested for proper function.

Responded to troubleshoot ongoing water system issues including recurring low water pressure, filter contamination with black sediment, and persistent leaking at the whole house water filter assembly. Conducted comprehensive inspection of the complete water system from well to point-of-entry equipment, examining all plumbing connections, pressure regulation components, and filtration hardware. Documented existing conditions with photographs showing the insulated pipe network, pressure gauge, filter housing with visible leak collection pans positioned beneath the assembly, and associated water treatment components. Identified the whole house filter as the primary source of leaking, which had progressed from an initial leak that temporarily stopped after filter replacement to a current slow drip condition. Noted significant black sediment accumulation requiring multiple filter changes within a short timeframe, indicating potential issues with well water quality or system contamination. E

Completed comprehensive air conditioning tune-up and maintenance on existing residential system approximately 3-4 years old. Performed standard inspection procedures including refrigerant level check, electrical component testing, condensate drain verification, air filter assessment, and overall system performance evaluation. All components found to be operating within normal parameters with no issues identified or repairs required.

Responded to service call for Daikin ductless mini-split system with four indoor heads. Inspected largest head unit located in dining room with reported louver malfunction. Confirmed horizontal venting option inoperative while vertical positioning remains functional, indicating internal louver gear mechanism failure. Upon opening unit for inspection, discovered significant dust and lint accumulation on internal components and blower assembly, which can contribute to mechanical binding and premature wear of moving parts. System otherwise operating normally with adequate cooling performance. Discussed repair options with customer, including louver motor/gear assembly replacement. Noted unit age at 15-20 years and discussed system obsolescence concerns. Customer aware that replacement parts availability may be limited due to age of equipment. System continues to provide cooling function with vertical airflow direction. Recommended monitoring system performance and provided options for rep

Performed comprehensive air conditioning tune-up and maintenance on Rheem system installed in October 2016. Completed inspection of outdoor condenser unit, cleaned outdoor coil, and verified proper system operation. Also conducted gas furnace tune-up on matching Rheem equipment from same installation date, with last service performed in September 2021. Noted previous observation of potential water heater leak that requires further investigation when area around unit is accessible for proper assessment.