HVAC & Plumbing Services in Breinigsville, PA

Replaced fiberglass well tank and tee package assembly in mechanical room. Installation included new plumbing connections with flexible hoses, metal fittings, and copper piping to ensure proper water pressure and flow from the well system.

Completed installation of new 1/2 HP garbage disposal unit to replace non-functioning unit. Addressed kitchen sink clog issue and installed upgraded disposal model with improved grinding capabilities. All connections secured, system tested and verified operational.

Installed a complete water treatment system in basement consisting of a UV water disinfection unit and whole house filtration system. Integrated both units into existing copper supply lines with new shut-off valves, brass fittings, and proper mounting hardware secured to wooden backing boards on foundation wall. Configured plumbing to allow UV disinfection following filtration stage, ensuring optimal water quality throughout the residence.

Completed full system change-out of failing HVAC unit #2, installing new Moyer Comfort Series air conditioning system. Installation included new air handler with proper refrigerant line connections, updated ductwork with reflective insulation, and system charging verified with electronic scale showing proper refrigerant levels. All mechanical components, piping, and electrical connections tested and operational.

Responded to dispatch call and confirmed arrival window with customer. Upon inspection, discovered an additional leak beyond the original reported issue. Documented conditions with photographs showing water damage evidence at floor and wall junction areas. Customer to proceed with previously provided quote for water treatment work.

Replaced malfunctioning System 2000 zone valve control board that was experiencing buzzing and displaying multiple fault indicators. New board was installed and tested, with all zones now operating properly and system functioning as designed.

Responded to low refrigerant call and added 1.9 lbs of R-410A refrigerant along with UV dye to system. Upon follow-up inspection, UV dye successfully identified active leak at lineset connection point, confirming refrigerant loss and need for repair.

Serviced multi-zone HVAC system by installing and wiring zone damper control panel with multiple zone modules and thermostat connections. Verified proper operation of all zone dampers and confirmed system functionality in attic installation area.

Responded to no cooling complaint on 410A residential system with frozen evaporator coil. Found indoor coil iced over with circulation fan running but compressor off. Allowed system to thaw completely, then performed leak check and system diagnostics. Identified refrigerant loss as primary cause of freeze condition. Evacuated remaining refrigerant, performed vacuum test to verify system integrity, and recharged system to manufacturer specifications using calibrated electronic charging scale. Verified proper airflow, confirmed filter had been recently replaced, and tested system operation with normal temperature differential and no freeze-up upon restart.

# After Hours Emergency Service Responded to emergency call for water treatment system malfunction. Upon arrival, found dual-tank Marlo water softening system with control unit displaying error codes. Inspected both fiberglass tanks and associated plumbing connections. Diagnosed control valve failure on primary softener unit causing system to lock out. Reset control head, verified proper operation of brine draw cycle, and tested water flow through both treatment vessels. Checked copper supply lines and blue PVC distribution piping for leaks or restrictions. Confirmed system returned to normal automated regeneration cycle. Verified water quality output and ensured all electrical connections were secure. System restored to full operational status.

Completed comprehensive preventive maintenance inspection on heat pump system with indoor unit located in crawl space accessed through interior closet. Removed items from closet to access trap door entry point and utilized 6' step ladder to reach equipment. Performed thorough cleaning of evaporator coil and outdoor condenser unit with coil cleaner as part of cooling season tune-up. Inspected blower motor assembly, electrical connections, and ductwork system including flexible ducts and rigid metal supply lines. Verified proper insulation placement around ductwork in attic space. Checked motor wiring connections including yellow, red, and white wire terminals. System operating within normal parameters following maintenance completion.

# After Hours Emergency HVAC Service Responded to emergency call for non-functioning heating system. Upon arrival, discovered evaporator coil completely frozen with heavy ice accumulation on fins and refrigerant lines. System was shut down immediately to prevent compressor damage. Investigation revealed restricted airflow as primary cause of freeze-up condition. Allowed coil to thaw completely while inspecting entire system. Checked air filter and found severely clogged, restricting airflow to approximately 30% of required capacity. Replaced dirty filter with new high-efficiency filter. Inspected blower motor operation and verified proper function once ice melted. Used digital multimeter to test electrical components including capacitors, contactors, and safety switches. All electrical readings within manufacturer specifications. Verified proper refrigerant pressures once system thawed and confirmed no refrigerant leaks present. Checked condensate drainage system for blockages. Cle

Completed comprehensive air conditioning tune-up and maintenance on residential HVAC system originally installed in August 2018. Performed diagnostic temperature measurements on condenser unit, recording ambient temperature readings of 82.7°F at the heat exchanger assembly. Inspected radial fin condenser coil and verified proper airflow through the unit, with all fins intact and properly aligned for optimal heat transfer efficiency.

Completed preventive maintenance inspection on Goodman heat pump system in cooling mode. Performed comprehensive tune-up including temperature diagnostics, electrical component inspection, and blower motor evaluation. Supply air temperature measured at 47.3°F, indicating proper cooling operation. All electrical connections, contactors, and wiring verified secure and functioning correctly. Blower assembly and condensate system inspected with no issues found.

Completed comprehensive preventive maintenance inspection on Rheem heat pump system installed in 2016. Removed and thoroughly cleaned heavily soiled blower wheel assembly, removing significant dust and debris accumulation from blades and housing to restore proper airflow and system efficiency. Performed complete heat pump tune-up including inspection of outdoor unit components, refrigerant levels, electrical connections, and overall system operation to ensure optimal cooling performance.

Responded to service call for Burnham Altac propane combi boiler experiencing thumping noise during operation that ceases when domestic hot water is activated. Performed diagnostic inspection of unit installed in April 2025. Inspected internal components including blower motor assembly, heat exchanger, three-way valve operation, and control board functionality. Reviewed manufacturer troubleshooting guide to identify potential causes related to water flow, air in system, and valve cycling. Documented system operation and captured images of internal components and diagnostic reference materials for further analysis.

Responded to after hours emergency call for mechanical equipment issue. Upon arrival, found significant damage to foil-faced insulation material on interior ductwork panel within utility cabinet, with tears, compromised reflective surface, and exposed underlying fibrous material. Evidence of moisture intrusion observed on concrete base with visible staining and discoloration, indicating potential water damage contributing to insulation deterioration. Documented existing conditions with photographs for service records.

Performed comprehensive inspection on 2-year-old Carrier natural gas heating system with zoning issues. Examined internal components including motor assembly, electrical wiring, and control systems. Identified significant temperature differential between floors (89°F in upstairs loft vs 72°F downstairs) and inspected Honeywell smart thermostat that had previously malfunctioned. Observed filter drier component with copper piping showing signs of corrosion that may be contributing to the zoning performance problems.

Responded to service call for 17-year-old natural gas furnace with reported high-pitched noise during operation. Upon inspection, found worn blower motor bearings causing noise; verified burner assembly functioning properly with normal flame pattern and no signs of heat exchanger issues. Replaced blower motor assembly, lubricated all necessary components, and performed operational test to confirm normal system function with noise eliminated.

Completed annual tune-up on Burnham Alta combi boiler (installed April 2025). Inspected control panel interface and accessed diagnostic codes to verify proper operation. Re-routed condensate line using 3/8" PEX coupling as required.

Successfully replaced defective AO Smith water heater under manufacturer warranty. Installed new unit with proper copper pipe connections, ensuring all plumbing fittings were correctly soldered and leak-free. Verified proper operation of all valves and connections before completion.

Inspected A.O. Smith Signature water heater reporting leakage at base. Performed visual examination of tank exterior and plumbing connections. Identified and repaired leak at copper pipe fitting junction where corrosion had developed, resolving the issue without need for tank replacement.

Replaced leaking Delta shower head with customer-supplied parts, ensuring proper installation and testing for water-tight seal. Inspected adjoining handheld shower wand connection for potential issues and verified full system functionality before completion.

Responded to service call for a Combi boiler with no hot water and no heat. Inspection revealed pressure regulation issues with the system. Adjusted the pressure regulator valve and verified system pressure readings on the temperature/pressure gauge to restore proper operation of heating and hot water functions.

Garbage disposal making loud noise