HVAC & Plumbing Services in Mertztown, PA

Responded to service call for residential air conditioning system blowing warm air with inadequate cooling performance. Upon inspection, identified issues with refrigerant line connections and electrical wiring at outdoor condenser unit. Secured copper refrigerant lines in mounting bracket with proper insulation sleeves to prevent thermal loss. Verified and reconnected electrical connections at junction box using appropriate wire connectors to ensure proper power supply to compressor and condenser fan motor. Tested system operation and confirmed proper cooling function restored with adequate airflow and temperature differential.

Completed comprehensive air conditioning tune-up and maintenance inspection on a 5-year-old Lennox heat pump system with LP backup heat. Performed multi-point system evaluation including inspection of electrical components, circuit boards, wiring connections, and condenser unit operation. All components found to be functioning properly with no issues identified during the inspection.

Responded to follow-up service call for cooling performance verification after recent after-hours assistance. Performed comprehensive system inspection of upstairs air conditioning unit. Conducted visual examination of exterior condensing unit and interior air handler components, including ductwork and insulation integrity in attic space. Verified system operation, airflow, and cooling output. Documented equipment condition with photographs showing exterior unit installation, electrical connections, and attic ductwork routing. System confirmed operational with adequate cooling capacity. Advised on proper filter maintenance for upstairs unit.

Completed blower wheel cleaning on HVAC system as previously sold and scheduled. Unit interior showed significant accumulation of dirt and debris on blower wheel assembly, which was thoroughly cleaned to restore proper airflow and system efficiency.

Completed comprehensive air conditioning tune-up and system inspection. Performed thorough evaluation of electrical components including capacitor and control board functionality, verified all wire connections within the control panel, and inspected the air handler unit located in the crawl space. All components found to be operating within normal parameters, and membership program options were presented to the customer.

Responded to customer complaint regarding excessive indoor humidity levels causing damage to wooden furniture and flooring during cooling season. Documented HVAC system specifications and current operating parameters for future diagnostic work scheduled when ambient conditions allow proper system evaluation. Customer reported humidity-related wood swelling has decreased by approximately 1/4" since switching to heating mode, confirming correlation between AC operation and moisture issues requiring further investigation of system dehumidification performance.

Performed CPM A/C inspection on SmartComfort system installed in October 2023 with 16x25x1 filter. Investigated customer concern regarding condensate drainage system after homeowner discovered disconnected condensate tubing exiting the home with no proper connection to remove water from underneath the structure. Inspected condensate line routing, verified system operation, and documented equipment labels and exterior condensate discharge point with photos to assess proper drainage functionality and determine necessary repairs to condensate piping system.

Responded to cold water leak under mobile home where crimped tee fitting was identified as the source of the leak. Replaced leaking polybutylene tubing with PEX piping for both hot and cold water lines in the crawl space. Water had been shut off to the home prior to arrival and was restored upon completion of repairs.

Performed maintenance inspection on Fleck 560 water softener system experiencing excessive salt consumption, which had doubled from normal usage of 40 pounds to 80 pounds per month. Conducted comprehensive water quality testing and water pressure diagnostics to assess system performance. Upon inspection, noted that resin media has not been replaced since original installation in October 2014, indicating need for future media replacement to restore proper regeneration efficiency and salt consumption rates.

Replaced two shut-off valves feeding the bathroom to eliminate active leaking before customer's vacation. Installed new quarter-turn ball valves on copper supply lines to ensure reliable water control and prevent potential water damage during extended absence.

Water softener check

Leaking drain line

Completed multi-point repair on residential HVAC system requiring two-person crew. Re-leveled downstairs indoor air handler unit, performed blower wheel cleaning to restore proper airflow, replaced two failed capacitors (verified with diagnostic testing equipment), and installed new condensate float switch to prevent overflow issues.

Responded to service call for Lennox air conditioning system not maintaining temperature with indoor unit freezing up in basement. Upon inspection, found evidence of previous refrigerant addition and signs of system age with visible corrosion on components. Diagnosed freezing coil condition, documented electrical connections at outdoor unit and indoor air handler condition with rust present on mounting brackets and housing. System installed approximately 11 years ago with recent filter change completed by occupant prior to service visit.

Responded to after-hours emergency for reported toilet leak. Upon arrival, inspected bathroom plumbing fixtures and identified water seepage from toilet supply line connection at the angle stop valve. Tightened compression fitting on braided supply line and verified all connections at the chrome shut-off valve were secure. Tested system by cycling water supply and flushing toilet multiple times to confirm leak was resolved with no further water discharge observed.

Responded to service call for comfort height toilet experiencing incomplete tank filling, resulting in inadequate flushing performance. Upon inspection, found toilet tank with significant mineral deposits, staining, and discolored water indicating aging flush valve and fill valve assembly. Tank required manual valve manipulation to achieve proper water level for effective flush. Performed mid-job assessment and presented repair options including immediate repair, partial tank rebuild, complete tank rebuild, standard flush toilet replacement, pressurized flush toilet replacement, and flange repair as needed. Documented existing water damage to surrounding flooring and baseboard, showing extensive staining and discoloration. Deployed water extraction equipment to address moisture issues in affected area. Adjusted fill valve mechanism and tested flush cycle to restore proper tank filling and flushing operation.

Responded to water system shutdown issue affecting household water supply. Replaced failed well pressure tank with new WR-80 model in utility room beneath stairs. Installed stainless steel tank tee to improve system configuration and water flow management. Added unions on water heater connections to facilitate future maintenance and service access. Shut down water supply to complete installation safely. Reconnected all plumbing lines, tested system operation, and verified proper pressure cycling and water delivery throughout the residence.

Responded to complaint of inconsistent water pressure with intermittent loss of water flow. Diagnosed failed pressure switch on well water pressure tank system. Removed and replaced defective pressure control switch and associated electrical connections. Disassembled corroded tank components showing signs of sediment buildup and internal corrosion. Reinstalled system with new hardware and clamps, verified proper electrical connections, and tested pressure cycling to confirm consistent water pressure restoration throughout property.

Completed comprehensive air conditioning tune-up on a Goodman system installed in 2007. Performed thorough cleaning of outdoor condenser unit, which had not been serviced since original installation, removing debris and buildup from cooling fins and fan assembly. Inspected indoor air handler unit located in attic, noting dust accumulation on blower wheel and housing. Conducted standard maintenance procedures including checking refrigerant levels, testing electrical connections, verifying proper airflow, and assessing overall system operation. System is functioning within normal parameters; customer was advised of findings and any recommendations for optimal performance.

Performed comprehensive heat pump maintenance and system inspection per early season tune-up protocol. All system components operating within normal parameters with no issues identified. Documented zone damper actuator motor condition and wiring connections, confirming proper operation of all mechanical and electrical components throughout the system.

Completed comprehensive AC tune-up and maintenance on 15-year-old central air conditioning system. Performed thorough inspection of all components including refrigerant lines, connections, and ductwork, with all systems operating within normal parameters. Discussed available service options with customer as alternative to duct cleaning services.

Responded to no cooling complaint on Daikin AC system installed in November 2023. Upon arrival, confirmed indoor unit fan operating continuously but outdoor condenser unit not running, resulting in thermostat reading 78°F despite setpoint of 69°F. Diagnosed failed capacitor on outdoor unit. Removed and replaced defective capacitor, restoring proper operation to condenser unit and cooling function to system.

Completed installation of Hague water softener and neutralizer system to address water quality concerns. Repaired water lines near crawl space area where leak was identified, with house main shut off during repair work. Addressed air in water lines and rattling pipes issue reported by homeowner, ensuring proper system operation and water flow throughout residence upon completion.

Completed comprehensive air conditioning tune-up and preventive maintenance on American Standard system manufactured in December 2017. Performed standard inspection procedures including refrigerant level verification, electrical component testing, condenser coil cleaning, and overall system performance evaluation. Additionally completed previously recommended blower wheel cleaning to address mold buildup, which required customer approval prior to service execution.

Completed comprehensive air conditioning maintenance check on heat pump system installed in April 2021. Performed thorough inspection of outdoor condensing unit, including examination of condensate drain lines, electrical connections, and refrigerant lines with foam insulation. Inspected indoor air handler unit located in attic space, verified proper operation of all components, and documented system condition with photographs for service records.