HVAC & Plumbing Services in Kutztown, PA

Responded to service call for toilet leaking into basement when flushed. Upon arrival, water supply had been shut off to prevent further damage. Inspected two-piece toilet installation, tank components, and flush mechanism to identify source of leak. Completed necessary repairs to resolve leak issue and restore proper toilet function without water entering basement area.

Responded to emergency plumbing call for pinhole leak on copper water main supply line entering residence. Upon arrival, found active leak with temporary container in place for water collection. Performed repair on compromised copper piping section in crawl space area. Conducted water quality testing to assess pH levels and documented findings with photographs per protocol. Based on water test results, provided quote for recommended water treatment system to address corrosive water conditions contributing to copper pipe degradation. Confirmed appointment time prior to arrival and completed all work as scheduled.

Responded to recurring basement leak issue. Upon initial visit, replaced wax ring on toilet. Customer reported continued leaking and opened wall sections to facilitate leak detection and access for repairs. Investigated exposed plumbing system within wall cavity, taking measurements of affected areas. Identified leak source requiring additional repairs. Kitchen plumbing temporarily out of service pending completion of necessary repairs to water supply lines or drain system within wall structure.

Responded to gas leak on newly installed direct vent gas water heater. Upon arrival, confirmed gas supply was shut off for safety. Inspected installation and identified improper blue plastic tubing used on gas supply line from street connection. Explained to homeowner that plastic tubing is not code-compliant for natural gas applications and poses serious safety hazard. Documented unsafe installation with photos showing the flexible plastic line connected to water heater and surrounding mechanical components. Recommended immediate replacement of plastic gas line with approved black iron pipe or corrugated stainless steel tubing (CSST) by licensed professional to meet code requirements and ensure safe operation.

Completed comprehensive oil heating system tune-up and maintenance service, including thorough cleaning and inspection of all components. System controls, limit switches, and electrical connections were examined and found to be operational, with noted recommendation for future blower wheel cleaning assessment during next scheduled air conditioning service.

Responded to no cooling complaint on Bryant air conditioning system installed in 1999. Upon arrival, performed diagnostic testing of both outdoor condenser unit and indoor air handler. Measured supply air temperature at register showing 17.9°F temperature differential, indicating inadequate cooling performance. Inspected outdoor unit fan operation and condenser coil condition. Evaluated airflow at supply vent to determine system performance issues. Completed full system diagnostics to identify root cause of cooling failure and provided recommendations for necessary repairs to restore proper operation.

Completed annual gas furnace tune-up and maintenance on one-year-old Ducane direct vent unit in new construction property. Performed comprehensive system inspection, cleaned blower wheel assembly, verified proper venting installation, and confirmed all components operating within manufacturer specifications.

Responded to service call for leaking 50-gallon electric water heater in residential basement. Upon inspection, confirmed active leak requiring full unit replacement. Removed existing Bradford White water heater and installed new 50-gallon electric water heater with adequate clearance specifications (23" width, 58" height). Connected copper supply lines, verified proper electrical connections, and tested all plumbing connections for leaks. System commissioned successfully with no issues detected.

Completed comprehensive preventive maintenance tune-up on Lennox heat pump system installed in March 2019. Performed standard CPM inspection procedures including checking electrical connections at outdoor disconnect, verifying proper airflow at interior supply registers, and evaluating overall system operation. All components found operating within normal parameters with no immediate service needs identified.

Completed water treatment system installation re-check and verified proper operation of the Smart Touch Control ST-400 unit. Performed water quality testing and documented system components including copper refrigerant lines, compressor assembly, and backwash cycle functionality to ensure installation meets specifications.

Responded to no-cooling complaint on Lennox AC system installed in September 2019. Upon arrival, verified thermostat was calling for cooling with setpoint at 71°F and indoor temperature reading 74°F in cooling mode. Inspected indoor air handler wiring and heat strip connections, confirmed all electrical connections secure with proper wire nutting. Customer had already replaced filter prior to service call. System was operational but failing to provide adequate cooling; performed diagnostic evaluation of thermostat operation and electrical components to identify cause of cooling failure.

Responded to emergency call for toilet leaking into basement. Upon arrival, confirmed active water leak requiring immediate attention and temporary containment. Removed existing failed toilet and installed customer-supplied replacement unit. Ensured proper sealing, secure mounting, and verified all connections were leak-free. Tested flush operation and confirmed no water intrusion to basement area below. Provided estimate for future installation of comfort height elongated bowl toilet with option for pressure-assisted model to accommodate accessibility needs. Also provided separate estimate for relocating washer and dryer hookups to third bedroom, including necessary plumbing modifications for water supply lines, drain connections, and venting requirements.

Responded to service call for water heater leaking at top of unit. Upon inspection, identified leak originating from plumbing connections at top of Rheem Performance Platinum electric water heater. Assessed all copper pipe fittings, brass valves, expansion tank connections, and pressure relief valve discharge piping. Tightened loose fittings and verified proper sealing of all connections. Tested system operation and confirmed leak was resolved with no further water discharge observed.

Responded to low water pressure complaint at residential well system. Upon arrival, found significant water accumulation in basement/crawlspace area requiring immediate attention. Performed diagnostic testing on well pump system using multimeter to check electrical components and capacitor functionality. Assessed submersible pump operation and verified proper electrical connections. Deployed pumping equipment to address standing water in affected area. Tested system voltage and capacitance to ensure well pump electrical components were operating within manufacturer specifications.

Completed comprehensive CPM oil heating inspection and cleaning service on New Yorker oil boiler system. Performed thorough cleaning of burner assembly, inspected all system components including circulator pump, expansion tank, and hydronic piping network. Verified proper operation of all safety controls, checked system pressures, and confirmed efficient combustion performance. All components found to be functioning within normal parameters with no immediate service needs identified.

Replaced 15-year-old 30-gallon electric water heater with new Bradford White unit due to leaking pipe at original water heater. Constructed wooden platform in closet location to properly support new installation, as existing flooring in original location required repair. Installed compression fittings and connected all water supply lines and electrical connections to restore hot water service.

Completed comprehensive plumbing inspection for property maintenance program. Replaced two leaking Hague drive assemblies and installed whole house automatic water shut-off valve. Assessed water filtration systems including reverse osmosis unit under kitchen sink with four filter elements, ice maker filter, coffee maker filter, and soda water filter. UV bulb for water treatment system requires replacement due to audible alert indicating end of service life. All replacement parts were available from warehouse inventory for immediate installation.

Responded to service call for Gibson AC unit (2013) with reported weak airflow and insufficient cooling. Upon inspection, discovered significant frost and ice accumulation on evaporator coil and refrigerant lines, indicating potential refrigerant leak or system restriction. Performed system diagnostics and obtained customer approval to proceed with refrigerant recovery and nitrogen pressure leak search test to identify source of system malfunction and determine necessary repairs.

Replaced existing toilet with white comfort height model to improve accessibility and user comfort. Installed handheld showerhead assembly to provide enhanced functionality and flexibility for bathing needs. Documented completed installations with photographs showing proper fixture placement and operational status of new showerhead.

Completed installation of Hague water softener system in basement utility area per approved estimate. System installed with proper copper piping connections, blue filter housing, and dual white storage tanks secured with black strapping. All components tested and operational upon completion.

Performed comprehensive air conditioning system tune-up and maintenance on existing residential HVAC system. Conducted thorough coil cleaning to optimize heat transfer efficiency and system performance. Completed full system diagnostic check including electrical measurements and control board inspection, confirming all components operating within normal parameters with no issues identified.

Responded to service call for water heater with reported lower element error. Upon arrival, confirmed unit was producing hot water. Performed diagnostic testing using digital multimeter on lower heating element assembly, obtaining voltage reading of 12.59V. Accessed electrical junction box and inspected wiring connections and wire nuts for proper installation. Documented existing conditions with photographs showing electrical components and testing procedures for service records.

Responded to service call for central air conditioning unit leaking water in basement mechanical room. Upon inspection, identified condensate drain line issue causing water accumulation. Cleared blockage from condensate drain system, verified proper drainage flow, and tested unit operation to ensure leak was resolved and system was functioning correctly.

Completed comprehensive heat pump tune-up and maintenance on Daikin Fit system installed in February 2024. Performed standard preventative maintenance procedures including inspection of indoor air handler unit located in attic space, verified proper refrigerant levels, checked electrical connections, and assessed overall system operation. All components found to be functioning within normal parameters with no immediate service concerns identified.

Responded to a call for a toilet leaking into the basement, confirmed by blue-tinted water visible below. Upon inspection, discovered a severely corroded and rusted toilet flange with significant deterioration at the floor connection point. Removed the toilet to access the damaged flange, replaced the failed flange with new hardware, installed a new wax ring seal, and properly re-set and secured the toilet to restore proper function and eliminate the leak.