HVAC & Plumbing Services in Breinigsville, PA

Performed gas furnace tune-ups on both the first- and second-floor Lennox systems, inspecting and servicing components for safe, efficient operation. Cleaned the first-floor blower wheel and housing, removing dust buildup to restore proper airflow and system performance.

Performed a complete gas furnace tune-up on an existing Carrier unit, including removal of the front access panel and inspection of the burner assembly, gas valve and piping, inducer/draft blower, blower motor, wiring harness, and PVC venting and drain connections. Verified thermostat operation, and found the system operating normally with no deficiencies. Noted light dust accumulation and minor rust-colored staining near the blower drain fitting, which should be monitored at future maintenance visits.

Performed a gas furnace tune-up and inspection in response to a reported water leak, finding water pooled around the base of the natural gas unit. Inspected the interior components, including the inducer blower housing and plastic collector box, where a hairline crack and sealant was noted near the condensate pipe fitting as a likely source of the leak. Verified operation with a digital thermometer probe on the ductwork (122°F reading) and completed the gas heating system check.

Responded to a burst pipe in the bathroom that had released water into the surrounding living space and required the main water supply to be shut off. Inspected the ceiling cavity and floor assembly below, locating the failed supply line and the resulting water damage, including a torn drywall section and moisture staining on the subfloor and joists. Isolated and repaired the leaking pipe, then restored water service and checked the system for leaks.

Inspected the upstairs toilet for a leak at the base and examined the tank internals, finding a heavily corroded float arm and fill valve with mineral buildup and sediment throughout the tank. Evaluated the supply line and shutoff valve connection and the base seal as potential leak sources, and documented the aged, rusted components as contributing to the water issue.

Performed annual cleaning and service on a 45-year-old Miller oil-fired furnace, including removal and cleaning of the burner assembly and replacement of the nozzle with a .60 x 80B. Inspected the blower compartment and squirrel cage wheel, noting dust accumulation on the blades and surface rust on the cabinet mounting bracket.

Performed seasonal maintenance on the Daikin air conditioning system and the York natural gas heating system. Inspected and tested system operation, and verified supply and return air temperatures with a digital thermometer (69.4°F and 50.7°F readings), indicating proper cooling performance and airflow. Confirmed the foil-faced ductwork and sealed joints were intact and the service tag was updated, with both systems operating normally at completion.

Installed customer-supplied faucet with company-provided deck plate on bathroom vanity. Installed new sage green Kohler Memoirs two-piece elongated toilet with concealed trapway and matching color caps on mounting hardware. Installed brass pop-up assembly and measured rusted ceiling vent in guest bath for replacement pricing.

Completed replacement of three white elongated bowl, comfort height toilets with standard flush mechanisms throughout the residence. Repaired wall damage at final toilet location and made all necessary water supply connections. Installed two customer-supplied showerheads and one customer-supplied lavatory faucet as additional scope items.

Performed re-check on K-2 combination boiler following previous fan speed adjustment. Inspected burner assembly and heat exchanger components, documenting conditions with photographs showing normal operational wear patterns and minor surface oxidation on internal components. Provided customer education regarding domestic hot water delivery times in relation to fan speed settings and proper system operation expectations for the 2019 natural gas unit.

Replaced fiberglass well tank and tee package assembly in mechanical room. Installation included new plumbing connections with flexible hoses, metal fittings, and copper piping to ensure proper water pressure and flow from the well system.

Completed installation of new 1/2 HP garbage disposal unit to replace non-functioning unit. Addressed kitchen sink clog issue and installed upgraded disposal model with improved grinding capabilities. All connections secured, system tested and verified operational.

Installed a complete water treatment system in basement consisting of a UV water disinfection unit and whole house filtration system. Integrated both units into existing copper supply lines with new shut-off valves, brass fittings, and proper mounting hardware secured to wooden backing boards on foundation wall. Configured plumbing to allow UV disinfection following filtration stage, ensuring optimal water quality throughout the residence.

Completed full system change-out of failing HVAC unit #2, installing new Moyer Comfort Series air conditioning system. Installation included new air handler with proper refrigerant line connections, updated ductwork with reflective insulation, and system charging verified with electronic scale showing proper refrigerant levels. All mechanical components, piping, and electrical connections tested and operational.

Responded to dispatch call and confirmed arrival window with customer. Upon inspection, discovered an additional leak beyond the original reported issue. Documented conditions with photographs showing water damage evidence at floor and wall junction areas. Customer to proceed with previously provided quote for water treatment work.

Replaced malfunctioning System 2000 zone valve control board that was experiencing buzzing and displaying multiple fault indicators. New board was installed and tested, with all zones now operating properly and system functioning as designed.

Responded to low refrigerant call and added 1.9 lbs of R-410A refrigerant along with UV dye to system. Upon follow-up inspection, UV dye successfully identified active leak at lineset connection point, confirming refrigerant loss and need for repair.

Serviced multi-zone HVAC system by installing and wiring zone damper control panel with multiple zone modules and thermostat connections. Verified proper operation of all zone dampers and confirmed system functionality in attic installation area.

Responded to no cooling complaint on 410A residential system with frozen evaporator coil. Found indoor coil iced over with circulation fan running but compressor off. Allowed system to thaw completely, then performed leak check and system diagnostics. Identified refrigerant loss as primary cause of freeze condition. Evacuated remaining refrigerant, performed vacuum test to verify system integrity, and recharged system to manufacturer specifications using calibrated electronic charging scale. Verified proper airflow, confirmed filter had been recently replaced, and tested system operation with normal temperature differential and no freeze-up upon restart.

# After Hours Emergency Service Responded to emergency call for water treatment system malfunction. Upon arrival, found dual-tank Marlo water softening system with control unit displaying error codes. Inspected both fiberglass tanks and associated plumbing connections. Diagnosed control valve failure on primary softener unit causing system to lock out. Reset control head, verified proper operation of brine draw cycle, and tested water flow through both treatment vessels. Checked copper supply lines and blue PVC distribution piping for leaks or restrictions. Confirmed system returned to normal automated regeneration cycle. Verified water quality output and ensured all electrical connections were secure. System restored to full operational status.

Completed comprehensive preventive maintenance inspection on heat pump system with indoor unit located in crawl space accessed through interior closet. Removed items from closet to access trap door entry point and utilized 6' step ladder to reach equipment. Performed thorough cleaning of evaporator coil and outdoor condenser unit with coil cleaner as part of cooling season tune-up. Inspected blower motor assembly, electrical connections, and ductwork system including flexible ducts and rigid metal supply lines. Verified proper insulation placement around ductwork in attic space. Checked motor wiring connections including yellow, red, and white wire terminals. System operating within normal parameters following maintenance completion.

# After Hours Emergency HVAC Service Responded to emergency call for non-functioning heating system. Upon arrival, discovered evaporator coil completely frozen with heavy ice accumulation on fins and refrigerant lines. System was shut down immediately to prevent compressor damage. Investigation revealed restricted airflow as primary cause of freeze-up condition. Allowed coil to thaw completely while inspecting entire system. Checked air filter and found severely clogged, restricting airflow to approximately 30% of required capacity. Replaced dirty filter with new high-efficiency filter. Inspected blower motor operation and verified proper function once ice melted. Used digital multimeter to test electrical components including capacitors, contactors, and safety switches. All electrical readings within manufacturer specifications. Verified proper refrigerant pressures once system thawed and confirmed no refrigerant leaks present. Checked condensate drainage system for blockages. Cle

Completed comprehensive air conditioning tune-up and maintenance on residential HVAC system originally installed in August 2018. Performed diagnostic temperature measurements on condenser unit, recording ambient temperature readings of 82.7°F at the heat exchanger assembly. Inspected radial fin condenser coil and verified proper airflow through the unit, with all fins intact and properly aligned for optimal heat transfer efficiency.

Completed preventive maintenance inspection on Goodman heat pump system in cooling mode. Performed comprehensive tune-up including temperature diagnostics, electrical component inspection, and blower motor evaluation. Supply air temperature measured at 47.3°F, indicating proper cooling operation. All electrical connections, contactors, and wiring verified secure and functioning correctly. Blower assembly and condensate system inspected with no issues found.

Completed comprehensive preventive maintenance inspection on Rheem heat pump system installed in 2016. Removed and thoroughly cleaned heavily soiled blower wheel assembly, removing significant dust and debris accumulation from blades and housing to restore proper airflow and system efficiency. Performed complete heat pump tune-up including inspection of outdoor unit components, refrigerant levels, electrical connections, and overall system operation to ensure optimal cooling performance.